Everyone wants to decorate their homes beautifully, but now the decoration market is hot, the price is not cheap, many people want to make a good renovation, but consider the funding problem and choose a simple decoration. In fact, saving money can also be beautifully decorated. For the knowledge of decoration , how much do you know? Then follow the decoration home network Xiaobian to learn about the relevant content!
1. Do not make the headboard of the shoe cabinet, leave a little space for the ash of the shoes to leak to the bottom, and install the lamp above the sink and gas stove. When you want to locate the floor drain of the bathroom, you must first think about it and measure the size. The floor drain is preferably located on one side of the brick. If it is in the middle of the brick, the floor drain will not be the lowest point no matter how the brick is tilted.
2. Regarding the treatment method of the corner of the brick, in the final analysis, it is to see the level of the worker. If the level of muddy workers is good, and the tools for grinding tiles are better, you should not hesitate to choose a 45 degree angle. From the effect point of view, as long as the grinding is good, the practice of grinding the angle of 45 degrees is the most beautiful! The most beautiful! If the level of the workers is really not good, then you still choose to use the angle bar, because the grinding A bad 45 degree angle is not as good as a positive angle.
3, the carpentry cover and the mason tiling are also to cooperate, when the door is covered, it is necessary to consider whether the ground below (any side of the two sides of the door) is still tiling or other cement mortar leveling, Because the door cover is nailed in front of the tile, it is always wrapped on the ground. When cement is used in the future, if the cement and the door cover are stained, it will cause the door cover wood to absorb water and mold.
4. After the door cover is completed, the muddy water worker begins to install the plaster line and the wall surface ash project. The wall of my house was originally flat, and 2-3 roads were fine. When the ash is approved, the ash is polished once, then the primer is applied. After the brush is finished, it is polished. Finally, the ICI brush is applied twice, and the whole wall looks smooth and flat, which is really good. After the wall ceiling project was completed, the woodworker began to make the wardrobe. The wardrobe is made of 18cm Weiye brand large core board, and the exterior is attached to the panel. Although it is not as good as the furniture store, it is durable and the quality should be better than the one bought.
5, must pay attention to the following points when tiling: it is best to be on the scene. Some of the less-perfect tiles can be placed in front of some invisible locations, such as cabinets, sinks, mirrors, etc., but also pay attention to tiles, waist tiles, etc. Don’t be stuck in the above position by the workers, otherwise you will have anything in the future. I can't see it, I still spend money. Before the wall tiles and floor tiles are attached, the watering time must be enough. Be sure to plug the floor drain with something to prevent the cement from going down.
The above is a detailed answer to the Xiaobian, I don't know if you are satisfied with the introduction of the decoration home network Xiaobian~ If you want to know more about the exciting content, please continue to pay attention to our decoration encyclopedia!
More related wonderful reading:
Decoration knowledge Daquan materials price decoration knowledge Daquan Feng Shui taboo
How is the kindergarten arranged? Kindergarten decoration knowledge
What is glazed brick? Glazed tile decoration knowledge
Decoration knowledge Daquan----decoration materials list
Decoration knowledge Daquan----eight major considerations
Fleixble Diamond Loop and Endless Wire Saw Diamond wire Loop with diamond wire saw is one of the flexibility cutting tool, setting the diamond crystals onto the steel surface and making one-way movement, mainly used for hard and brittle materials cutting, such as: sapphire, special ceramic materials , marble, tyre, rubber, stone, monocrystaline silicon, and polycrystalline silicon, etc.The flexible CBN and Diamond Wire from HANS will win you over with their high tensile strength, their strong grain bonding as well as the high quality of the diamond loop wire and the diamond grain. Diamond Loop/Endless Foam Wire Saw is one of the most flexible cutting tools, which can set on teh surface of diamond crystals. While cutting, the diamond wire will move from one direction with the speed from 30-60 m/s. It will give users the great advantages. Specification Outside Diameter 0.5-1.0mm is Continue Rim Outside Diameter 1.0-1.5mm can Continue Rim or Segment Rim Outside Diameter 1.5-3.0mm is Segment Rim High efficiency on cutting, while the speed from 30 to 60 m/s Diameter from 0.3-3.0 mm,Length from 800-50000 mm and math for the popular machine in current market Cutting fits into both wet or dry environment Cutting directions could change by customer's requirement. And also could apply to cut the curved surface. Operation and Replacement of diamond wire are really convention Diamond Loop Wire Saw is one of the most flexible cutting tools, which can set on the surface of diamond crystals. While cutting, the diamond wire will move from one direction with the speed from 30-60 m/s. It will give users the great advantages. Widely used on cutting the rubber machine and hard surface of materials,such as,tire Section cutting machine,Tyre section cutting machine,artificial crystal (sapphire, silicon),Special Ceramic,Precious metal,graphite and plastic,brittle material. Also used on research field: geology,archaeology,architecture and biology etc. Also supply the diamond loop wire saw for tire section cutting machine. Compared with other diamond cutting tools, the Loop diamond wire is a flexible tool: 1)Not only can be used for straight line cutting, but also curved surface cutting; 2)Not subject to the shape of the surface of the object; 3)The workplace requires simply, but large area cutting can be carried on; 4)The use of diamond wire saw can improve resource utilization and reduce environmental pollution. Due to the above advantages, the market shares of diamond wires are getting bigger and bigger, and the scope of application is getting wider and wider. As many of our clients can testify, Hans Service and Support gives us the edge in our solutions.Whatever your requirements, We will be there for your immediate and long term needs.Professional Services & Consulting Tailored to Your Business. Excellent Products Quality; Perfect Application Solutions; Professional Technical Support; Prompt Delivery Time!
diamond coated wire,diamond wire saw machine,Diamond Loop Wire Saw, Diamond Endless Wire Saw,Tire Section Cutting Diamond Wire Saw,Diamond Precision Wire Saw, Foamglass Abrasive Wire Saw, Abrasive Wire Foam Cutting,Precision Diamond Wire Saw
Hans Superabrasive Material Co., Ltd. , http://www.hansuperabrasive.com