The recognition of the steel explosion-proof camera

In recent years, with the increase and expansion of coal mines, petrochemicals and other places, the discussion on explosion-proof cameras in the market has also begun to heat up. Explosion-proof cameras, by definition, can prevent explosions. Explosion-proof cameras monitor the steel in the camera. It is very important to master the knowledge of explosion-proof cameras.
In China's national standard 'GB3836.1-2000 Electrical Equipment for Explosive Gas Environments' and other 'GB3836.2-9' standards, explosion-proof grades have been clearly defined. And most of the anti-explosion grade parameters formulated by China are higher than European, American and international standards, which shows that China's management of explosion-proof equipment is very strict. At present, there are three types of explosion-proof cameras on the market: 'intrinsic safety type', 'positive pressure type', flameproof type
The 'intrinsically safe type' starts with limiting the energy in the circuit. Inside the camera, the potential spark energy is reduced to the ignitable prescribed gas mixture energy through reliable control circuit parameters. The surface heating temperature of the wire and component is limited to the specified gas. The ignition temperature of the mixture. All circuits inside the camera are intrinsically safe circuits that do not ignite the prescribed explosive atmosphere by any spark or any thermal effect that is produced under standard conditions (including normal operation and specified fault conditions). Type 'cameras are relatively expensive and are rarely seen on the market.
Positive-pressure type 'Ex-proof type' is to maintain continuous air or inert gas in the camera to restrict the flammable mixture from entering the camera through the housing.
The most common type of explosion-proof camera on the market today is a 'flameproof type' explosion protection type, in which the components of the camera that may ignite an explosive gas mixture are all enclosed in a single enclosure whose enclosure can withstand any joint or structural gap through the enclosure. The flammable mixture that penetrates into the interior of the enclosure explodes internally without damage and does not cause ignition of an external explosive atmosphere formed by one or more gases or vapours. Place parts of the camera that may produce sparks, arcs, and dangerous temperatures into a flameproof enclosure that isolates the interior of the camera from the surrounding environment. There is a gap in the flameproof enclosure. Due to the respiration of the electrical equipment and the gas permeation, an explosive gas mixture may be present inside. When the explosion occurs, the enclosure can withstand the explosion pressure generated without damage, and at the same time, the gap between the shell structure can cool the flame and reduce the flame. The speed of flame propagation or termination of the acceleration chain prevents flames or dangerous flame products from igniting the external explosive atmosphere through explosion-proof gaps, thereby achieving the goal of flameproofing. Therefore, many of these flameproof enclosures are the main security companies, such as Shenzhen Wanwan. Cheng Technology Co., Ltd.
In fact, there are almost the same elements needed to produce an 'explosion' and 'burn'. Three conditions must be met at the same time. First, there must be explosive or flammable substances; second, there must be flammable substances, mainly in the air. Oxygen; third, there is also a source of ignition (such as sparks, arcs, and dangerous temperatures, etc.) that provide the energy necessary to ignite the mixture. Only if these three conditions exist at the same time will there be the possibility of an explosion. If any of these conditions is not met, there will be no burning or explosion. In the mines, chemical plants, military factories, arsenals, oil fields, oil depots and other dangerous goods production or storage, the first two conditions are basically met, and the third condition is the cameras introduced by the contractor because of the sealing performance of ordinary cameras. It is impossible to prevent the inflammable gas from entering the body, and the electronic components of ordinary cameras may generate sparks, arcs, and dangerous temperatures during normal operation. Therefore, the combustible gas entering the casing is encountered, and thus the installed camera is not only unsafe. The original intention was to become a 'time bomb'. The real explosion-proof camera manufacturing principle is also nothing more than to make the above three conditions not available at the same time, it really played the role of explosion-proof.
As people's safety awareness gradually increases, the field of application of anti-explosion-proof cameras should be wider and wider in theory, but in fact, the amount of explosion-proof cameras is not very large. Why?
1. The most important reason is cost. The price of an explosion-proof camera is a lot higher than that of an ordinary camera with the same parameters. Domestic engineering companies and users do not have a high degree of acceptance of these high-priced products. They still need time to cultivate and change their consumer attitudes and awareness, which greatly restricts the popularity of explosion-proof cameras.
2. The second reason is that there is not enough awareness of the need for 'explosion protection'.
3. The third reason is that the surrounding facilities are not enough 'explosion-proof'. Even if an explosion-proof camera is not equipped with explosion-proof back-end equipment or professional construction, it will not be able to exert the effect of explosion-proof. For example, explosion-proof heads are not used, or the transmission wires are exposed and there are potential safety hazards.

A study on controlling chloroform in drinking water using chlorine dioxide as first disinfector followed by chlorine as secondary disinfector was reported. Using chlorine dioxide as pretreatment disinfector would decrease the concentration of chloroform in drinking water. Chlorination after chlorine dioxide pretreatment may be influenced by reaction time and temperature. Additionally, when the mixture which composed of chlorine and chlorine dioxide was used, with the content of chlorine dioxide in mixture disinfector increasing, chloroform in the sample treated by it may decrease obviously.

Medical Industry Disinfection

Medical Wastewater Chlorine Dioxide, Medical Disinfection Chlorine Dioxide, Hospital Environment Disinfection Cio2, Medical Instrument Disinfection Cio2

Nanjing Ligong Shuifu Environmental Protection Technology Co.,Ltd. , http://www.watermanclo2.com

Posted on