What are the common faults of open-air installation wing gates? Wing gates are generally not allowed to be used in the open air. Because the wing gate is basically not waterproof, this can also be seen from the structure. Before installation, the manufacturer will inform customers that open-use failure rates will be high.
Wing gate faults generally have the following types:
1. Control board or small components can cause damage. After the water splashes in the chassis, after high temperature transpiration, water droplets will adhere to the control board or components. After a certain period of time, the control board or components will cause short circuit or premature aging.
2. The infrared radiation device will be damaged or malfunction. Because of the harsh environment in the open air, coupled with dew in the gates after rain and snow weather, the probes on the radios will send tiny droplets of water, causing the detection to malfunction and causing the channel to continue to alarm. Therefore, it is strongly recommended that every effort be made to build a canopy for customers. Otherwise, customer satisfaction with the product is a problem in the long term.
In addition, the following issues need to be taken into account when trying to extend the service life of a wingblade:
Wing gate chassis is sprayed or painted by No. 304 stainless steel and electrolytic board (A3 board). Stainless steel chassis has a rust spot for a long time. Clean the chassis with sandpaper and green gauze and fossil powder. The sanding surface is rubbed along the long lines ( Protecting the direction of thick lines. Otherwise it will affect the appearance. The mirror surface is polished with a polishing wheel and polishing wax, and the conditional appearance is coated with anti-rust oil. Spray, paint the chassis, use a soft cloth to wipe off the dust, the appearance of scratches with the same color of paint to make up, do remember to put the radio eye where the paint, once the cover with wings, The gate will falsely alarm and cause unnecessary trouble.
Periodically clean the surface dust, spray the drive part with butter, apply the butter to the gear and wheel groove, and fix the motor according to the original position. Check if there is any looseness in the screw of the connecting piece. Tighten the limit switch and the limit metal sheet. , 1-2mm too far away from the gap, too close to easily damaged.
The above is the common fault of open-air installation of wing gates. I hope to be helpful to everyone. I am grateful to the new and old customers for their concern and support for innovation and technology for many years. I would like to thank everyone for the new year and wish everyone a new year. Prosperity, all things Shunan.
Wing gate faults generally have the following types:
1. Control board or small components can cause damage. After the water splashes in the chassis, after high temperature transpiration, water droplets will adhere to the control board or components. After a certain period of time, the control board or components will cause short circuit or premature aging.
2. The infrared radiation device will be damaged or malfunction. Because of the harsh environment in the open air, coupled with dew in the gates after rain and snow weather, the probes on the radios will send tiny droplets of water, causing the detection to malfunction and causing the channel to continue to alarm. Therefore, it is strongly recommended that every effort be made to build a canopy for customers. Otherwise, customer satisfaction with the product is a problem in the long term.
In addition, the following issues need to be taken into account when trying to extend the service life of a wingblade:
Wing gate chassis is sprayed or painted by No. 304 stainless steel and electrolytic board (A3 board). Stainless steel chassis has a rust spot for a long time. Clean the chassis with sandpaper and green gauze and fossil powder. The sanding surface is rubbed along the long lines ( Protecting the direction of thick lines. Otherwise it will affect the appearance. The mirror surface is polished with a polishing wheel and polishing wax, and the conditional appearance is coated with anti-rust oil. Spray, paint the chassis, use a soft cloth to wipe off the dust, the appearance of scratches with the same color of paint to make up, do remember to put the radio eye where the paint, once the cover with wings, The gate will falsely alarm and cause unnecessary trouble.
Periodically clean the surface dust, spray the drive part with butter, apply the butter to the gear and wheel groove, and fix the motor according to the original position. Check if there is any looseness in the screw of the connecting piece. Tighten the limit switch and the limit metal sheet. , 1-2mm too far away from the gap, too close to easily damaged.
The above is the common fault of open-air installation of wing gates. I hope to be helpful to everyone. I am grateful to the new and old customers for their concern and support for innovation and technology for many years. I would like to thank everyone for the new year and wish everyone a new year. Prosperity, all things Shunan.
Hunting Knife Kits,Handmade Hunting Knife,Handmade Pocket Knife,Handmade Knife
YangJiang Junxiong Trading & Industry Company Co.,Ltd , https://www.cn-sundo.com