Most consumers may have this question: How to distinguish the quality of the cabinet from the appearance of the good and bad, we can not go to each cabinet processing plant to understand, but it does not matter, today Xiaobian take everyone to see the cabinet processing plant How the old employee identified the cabinet from the outside.
Look at the cutting board
Cutting board, also known as sheet blanking, is the first step in the production of cabinets. The large-scale specialized enterprises use electronic cutting saws to input the processing dimensions through the computer, and the computer controls the dimensional accuracy of the material selection, and can process several sheets at a time. The performance of the equipment is stable and the precision of the panel size is very high. The tolerance unit is in micrometers, and There is no collapse phenomenon on the edge of the board. The hand-workshop-type small factories use small manual cutting saws, and even use a woodworking open-saw to build a simple operation table. The board size produced by this kind of simple equipment is often larger than 1mm, and often occurs. The collapse phenomenon, that is, the sheet substrate is exposed.
Look at the edge of the plate
When buying a cabinet, you may wish to touch the edge of the cabinet with your hands. The cabinets of the high-quality cabinets are exquisitely sealed, smooth, and feel good. The sealing lines are straight and smooth, and the joints are fine. Professional manufacturers use a linear edge banding machine to complete the sealing, decapitation, trimming, chamfering, polishing and other processes at one time. The coating is even and the pressure on the sealing edge is stable. Each station on the assembly line works continuously to ensure the most accurate dimensions. . The workshop-style small factory uses a brush to apply glue, artificially presses and seals the edge, uses a paper knife to trim the edges, and uses a manual polishing machine to polish. Due to the uneven coating, the edges and ridges that are produced are uneven, and the sealing line is undulating. Even the sealer has a rowing feel. Due to the uneven pressure, many places are not strong, and it is easy to open and detach the rubber in a short time. Once the edge is peeled off, there will be water, swelling, and a lot of formaldehyde and other toxic The gas evaporates into the air, causing harm to the human body.
Look for punch
Today's panel furniture is assembled on three-in-one connectors, which requires a lot of positioning holes in the panel. The fit and accuracy of the hole position will affect the structural integrity of the cabinet cabinet. Professional manufacturers use 32 magic multi-row drills to complete a number of holes on a board edge and board surface at a time. These holes are a positioning reference, so that the accuracy of the dimensions is guaranteed when the holes are mated.
Watch door
The door is the face of the cabinet and is as important as the person's face. Everyone wants to choose a good-looking “face†for their cabinets, and distortion-distorting “faces†are certainly not included in the selection.
See the assembly effect of the whole cabinet
Cabinet, the gap should be uniform. Any dimensional error in the production process will be displayed on the door panel. The door panels produced by professional manufacturers are horizontal and vertical, and the gap between the doors is even. The cabinets and door panels of the small factory production will have uneven door gaps and uneven gaps. Big and small, so the door is not on a plane .
Look at the drawer slides
Although it is a small detail, it is an important part of the quality of the cabinet. Due to the dimensional error of the hole position and the plate, an error occurs in the mounting size of the slide rail, causing the drawer to be pulled unsmoothly or left and right to loosen.
Information about the cabinet processing plant was introduced here for everyone. I hope this article will be helpful to everyone. If you still have something you don't understand, you can leave a message to Xiaobian at the bottom. We will answer your questions as soon as possible.
Kitchen Cabinets Kitchen Cabinets Custom Cabinets Furniture Cabinets Doors Drawers Cabinets Doors
The coal carrier activated carbon has well-developed pore structure, good adsorption property, high mechanical strength, easy to repeat regeneration, low cost, and so on, it is used for purifying the poisonous gases, treating the waste gas, purifying the industrial and domestic water, and recovering the solvent.
Use: Used in the treatment of waste gases containing sulfureted hydrogen, methyl merecaptan, sulfur dioxide, methyl sulfide, dimethyl sulphide etc.
Spec.:
|
Model NO.
|
Moisture(%)
|
Strength(%)
|
Carbon tetrachloride(%)
|
Packing density(g/L)
|
Load content(%)
|
H2S(g/cc)
|
Grain diameter(mm)
|
| TZK-3070 |
≤15
|
≥95
|
≥70
|
≤660
|
KOH 6.0-8.0
|
≥0.140
|
Φ3.0
|
| TZK-4070 |
≤15
|
≥95
|
≥70
|
≤650
|
KOH 6.0-8.0
|
≥0.140
|
Φ4.0
|
| TZK-6070 |
≤15
|
≥95
|
≥70
|
≤630
|
KOH 6.0-8.0
|
≥0.140
|
Φ6.0
|
| TPK-4×8 |
≤15
|
≥95
|
≥60
|
≤580
|
KOH 5.0-7.0
|
≥0.140
|
3.6-3.8
|
| TPN-4×8 |
≤15
|
≥95
|
≥60
|
≤580
|
KOH 5.0-7.0
|
≥0.140
|
3.6-3.8
|
| TZI-4070 |
≤15
|
≥95
|
≥70
|
≤650
|
KI 2.0-6.0
|
≥0.140
|
Φ4.0
|
| TZS-4060 |
≤15
|
≥95
|
≥60
|
530-560
|
S 10.0-12.0
|
-
|
Φ4.0
|
| TPP-30×60 |
≤15
|
≥95
|
≥60
|
-
|
H3PO4 5.0-15.0
|
-
|
30×60 meshes
|
Coal Carrier Activated Carbon
Coal Carrier Activated Carbon,Coal Activated Carbon For Catalyst Carrier ,Coal Column Activated Carbon,Commercial Activated Carbon
SHIZUISHAN ZhongShi activated carbon co,.ltd , https://www.zscarbonchina.com