Cutting machine installation operation instructions-Dongguan Houjie heavy cutting machine installation operation instructions-Dongguan Houjie Heavy Machinery Co., Ltd.
First, the machine installation 1, the machine level is fixed on the flat concrete floor, check whether the parts of the machine are intact and firm, and the line is smooth and effective.
2. Remove stains from the upper platen and the work surface.
3. Inject 68# or 46# anti-wear hydraulic oil into the fuel tank, the oil surface should not be less than 25mm on the oil filter.
4. Connect the 380V three-phase power supply and press the oil pump start button to adjust and keep the motor steering in the same direction as the arrow.
Second, the operating instructions
1. First turn the cutting depth controller (fine tuning knob) to zero.
2. Turn on the power switch, press the oil pump start button, run for two minutes at no load, and observe whether the system is normal.
3. The push-pull plate, the rubber plate, the workpiece and the die are stacked in the middle of the workbench in order.
4. Pair the die (tool die setting).
1. Loosen the handle of the knife and naturally lower the bottom and lock it.
2. Turn the switch to the right and prepare for trial.
3. Double-click the green button to make a trial, and the punching depth is controlled by fine tuning.
4, fine-tuning: turn the fine-tuning button, the left-hand rotation is reduced, the right-hand rotation is deepened.
5. Stroke adjustment: Rotating the rise height controller, the right-hand rotation stroke is increased, the left-hand rotation stroke is reduced, and the stroke can be
It can be freely adjusted within the range of 50-200mm (or 50-250mm). In normal production, the upper pressure is about 50mm from the top of the die. Special Note: Each time the die, workpiece or pad is replaced, the stroke must be set again. Otherwise, the die and pad will be damaged.
Safety Precautions:
1. In order to ensure safety, it is strictly forbidden to extend the hand and other parts of the body into the punching area during operation. The power must be turned off before maintenance and the wooden block or other hard objects should be placed in the blanking area to prevent the pressure plate from being pressed. Loss of control, causing accidental personal injury. 2. Under special circumstances, when the upper pressure plate needs to rise immediately, press the reset button. When stopping, press the power brake button (red button), and the whole system will stop working immediately.
3. When operating, you must hit the two buttons on the pressure plate with both hands, and do not change one hand or pedal operation at will. Maintenance: Always keep the inside of the machine clean, the oil filter net is cleaned once a month, the hydraulic oil is changed once a year, and should be checked before work.
Check the oil level in the machine. When it is lower than the specified liquid level, it should be supplemented with the same grade of hydraulic oil in the machine. It should not be mixed. When cutting materials, the workpiece should be placed in the center of the work area to make the machine evenly distributed throughout the machine, extending the life of the machine from the surface.
Source of information: http://
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
Miscellaneous Spare Parts For Escalators
Miscellaneous Spare Parts for BLT Escalators, Xizi Escalators, CANNY Escalators, SJEC Escalators, KOYO Escalators, IFE Escalators, SELOON Escalators, HOSTING Escalators, Estilo Hosting Escalators, IMEM Escalators, KLEEMANN Escalators, Doppler Escalators, ORONA Escalators
BLT Escalator Spare Parts, Xizi Escalator Spare
Parts, CANNY Escalator Spare Parts, SJEC Escalator Spare Parts, IFE Escalator
Spare Parts
We can help you with high quality Miscellaneous Spare Parts
for BLT Escalators, Xizi Escalators, CANNY Escalators, SJEC Escalators, KOYO Escalators,
IFE Escalators, SELOON Escalators, HOSTING Escalators, Estilo Hosting
Escalators, IMEM Escalators, KLEEMANN Escalators, Doppler Escalators, ORONA
Escalators
We are the leading manufacturer & supplier of BLT Escalator Spare Parts, Xizi Escalator Spare Parts, CANNY Escalator Spare Parts, SJEC Escalator Spare Parts, IFE Escalator Spare Parts, Original Parts Guaranteed
Contact us TODAY for more Miscellaneous Spare Parts for BLT Escalators, Xizi Escalators, CANNY Escalators, SJEC Escalators, KOYO Escalators, IFE Escalators, SELOON Escalators, HOSTING Escalators, Estilo Hosting Escalators, IMEM Escalators, KLEEMANN Escalators, Doppler Escalators, ORONA Escalators
Miscellaneous Spare Parts for Escalators, Toshiba Escalator Spare Parts, SJEC Escalator Spare Parts, KOYO Escalator Spare Parts
CEP Elevator Products ( China ) Co., Ltd. , https://www.zjelevatordoorsystem.com